Vertical Machining Centers
Unmatched Performance By Master

The MV series is a flagship with unmatched machining performance. It is specially designed to exhibit optimal structure, high rigidity and high accuracy. In addition, its wide range of machining, powerful spindle motor as well as flexible machining capabilities make it ideal for upgrading industry.

1. The optional bed construction design is able to resist inertia generated by high "G" with maximum stability.‬

2. The short nose spindle presents outstanding rigidity. It also may increase efficiency while lowering tool wear.

3. Pneumatic counter-balance on Z-axis.

4. Front side chip exhaust with optimal chip exhausting angles and extra large chip flushing rate.

Vertical Machining Centers

Taiwan Master Tool Magazines.

• The entire series of machine employs‭ ‬Taiwan master tool magazines.

• The tool pockets are manufactured from aluminum alloy and T6‭ ‬treated for maximum durability‭.‬

• Front mounted air cylinder enables repair or maintenance to be accomplished in only 10‭ ‬minutes‭.‬

Short Spindle Nose

The short spindle nose design allows the spindle motor to fully develop transmission efficiency‭. ‬As a result‭, ‬machining accuracy‭ ‬is upgraded and spindle life is extended‭.‬

Ball Screw、Linear Motion Guide

The silent ball screws and linear guide ways on three axes feature high rigidity‭, ‬low noise‭, ‬low friction and high sensitivity‭, ‬providing an increase in machining speed and accuracy‭.‬

Pneumatic counter-balance on Z-axis

The Z-axis is designed with no counter-balance weight in combination with servo motor drive with brake to improve Z-axis drive performance‭. ‬Therefore‭, ‬high speed and better surface finish can be achieved‭.‬

Full-enclosed Guards

Fully enclosed guards ensure smooth movement at high speed and low noise‭. ‬The guards isolate coolant and chips and provide a protection for linear ways and ball screws for extending their service life‭.‬

machining center table

Table‭ size :

Coolant Jets Around Spindle

Coolant Jets Around Spindle

The coolant jets around spindle device employs 4 coolant nozzles around the spindle, that provides the best cooling effect to the tool and the workpiece resulting in better machining quality.

Direct Drive Spindle

Direct-drive Spindle(optional)

With the direct-drive design‭, ‬the motor is directly coupled to the spindle‭. ‬This feature may eliminate noise and backlash problems usually occured on a belt-drive or gear-drive system‭, ‬while providing a full-power rotation‭.‬

The spindle head is a symmetrical design to reduce thermal deformation due to temperature difference‭.‬

Floating type spindle tool knocking design prevents tool knocking force from directly exerting on the bearings‭, ‬that results in‭ ‬extended bearing life‭.‬

Roller Type Linear Guideway

Collision Protection Device

The machine is equipped with a collision protection device which can absorb and reduce the collision force. The machine accuracy is still maintained if any axis malfunction happens.

Large Capacity Coolant Tank

Large Capacity Coolant Tank

Cutting tank capacity of 200L, cutting calories can be quickly discharged.

Tank design uses door type, and placement of the rear side of the machine, saving space.

SPECIFICATION :

Model

MV-1685

Control unit

MITSUBISHI-MELDAS M70B‭ / ‬FANUC OiMD

Travel

X‭-‬axis travel

1600 mm

Y‭-‬axis travel

850 mm

Z‭-‬axis travel

800 mm

Spindle nose to table

150~950 mm

Spindle

Type of spindle

BT-40

Spindle transmission

Gear Head

Spindle R.P.M.

6,000 rpm

Spindle motor

15 kw

Feed

X/Y/Z rapid traverse

20 / 20 / 15 M/min

Three axes transmission method

Direct drive

Cutting feed rate

1~10,000 mm/min

Table

Table size

1700 x 800 mm

T-slot‭ ‬(‬WxNo‭.‬xPitch)

22 x 5 x 160 mm

Table loading capacity

2000 kg

A.T.C.

Tool selection method

ARM type

No‭. ‬of tools

24 / 32 pcs

Max‭. ‬tool weight

18 kgs

Miscellaneous

Coolant tank capacity

300 L

Max‭. ‬machine weight

10,450 kg

Machine‭ ‬size‭ ‬(LxWxH)‭‬

4550 x 4000 x 4000 mm

Air pressure

6 kg

Power requirement

35 KVA

•‭ ‬Design and specification are subject to change without prior notice‭.‬

Standare Accessories:

  • BT50 / 24 tools
  • 6,000 rpm gear head
  • Built-in coolant nozzles
  • Pneumatic counter-balance on Z-axis
  • Automatic lubrication system
  • M30 automatic power off
  • LED work ligh
  • Rigid tapping

    • Option Accessories:

  • 32 / 40 tools
  • Programmable coolant nozzle adjustment
  • 4th axis rotary table and tailstock
  • Automatic tool measuring device
  • Spindle oil cooler
  • Increase height of column
  • Screw type chip conveyor
  • Link chain type chip conveyor
  • Oil / fluid separation device
  • Coolant gun and air gun

    • Dynamic roundness inspection

    Laser inspection